Tripp Lite B160-101-DPHDSI 视频扩展器发射器/接收器,全高清1920x1080,1年保修,TAA合规,HDMI输入/输出,DisplayPort,RJ-45,双绞线,最大工作距离328英尺,黑色 特利普光电
Tripp Lite B160-101-DPHDSI 视频扩展器发射器/接收器,全高清1920x1080,1年保修,TAA合规,HDMI输入/输出,DisplayPort,RJ-45,双绞线,最大工作距离328英尺,黑色 特利普光电
Tripp Lite B160-101-DPHDSI
- Free Shipping
- 1年 保修
- 30天退货
- 碳中和
产品关键特征
- 以高清图像质量提供分辨率高达1920 x 1080(1080p)@ 60 Hz
- 发射机和接收机之间直接连接,无需交换机,最长可达328英尺
- 发射机的本地HDMI端口可让您监视远程显示器上显示的图像
- 即插即用,无需软件即可轻松、立即安装
- 符合联邦贸易协定法案(TAA)要求,可用于GSA计划采购
Tripp Lite B160-101-DPHDSI 视频扩展器发射器/接收器,全高清1920x1080,1年保修,TAA合规,HDMI输入/输出,DisplayPort,RJ-45,双绞线,最大工作距离328英尺,黑色 特利普光电
Tripp Lite B160-101-DPHDSI
- Free Shipping
- 1年 保修
- 30天退货
- 碳中和
小时
分钟
航运资讯
产品关键特征
- 以高清图像质量提供分辨率高达1920 x 1080(1080p)@ 60 Hz
- 发射机和接收机之间直接连接,无需交换机,最长可达328英尺
- 发射机的本地HDMI端口可让您监视远程显示器上显示的图像
- 即插即用,无需软件即可轻松、立即安装
- 符合联邦贸易协定法案(TAA)要求,可用于GSA计划采购
Tripp Lite
B160-101-DPHDSI
此传输器/接收器套件将DisplayPort音频/视频、RS-232串行和IR(红外)遥控信号从DisplayPort源(如笔记本电脑或媒体服务器)延伸并分发到DVI或HDMI显示器。这一点对点安装允许您将监视器、投影仪或电视放置在距离源头达328英尺(100米)的地方,比传统的Cat5e/6解决方案远200英尺以上。此外,通过添加一串未经管理的网络交换机(如Tripp Lite的NG5),您可以继续将源和显示器之间的距离延长至每个交换机328英尺。
扩展到超过328英尺的多输入多输出安装
您可以通过连接专用的具有Internet组管理协议(IGMP)的受管以太网网络交换机(如Tripp Lite的NSS-G16D2),创建具有多个源和显示器的安装。通过添加多个受管交换机,您可以创建具有最多64个发射机和255个接收器的多输入多输出安装。启用IGMP的交换机将允许您管理所有连接,从而集中控制哪些源显示在哪些显示器上。注意:未经管理的交换机安装限于两个发射机单位。接收器数量受限于未经管理交换机上剩余端口的数量。此传输器/接收器扩展器套件设计用于与专用网络交换机配合使用。连接与其他网络设备一起使用的交换机将导致性能下降或无法使用。
传输清晰的1080p视频与立体声音频
B160-101-DPHDSI支持在受管开关安装环境下的分辨率高达1920 x 1080(1080p),帧率为60 Hz,24位真彩色。它延伸了控制DisplayPort源的IR信号到远程显示器,以及串行波特率高达57600 Bps的RS-232信号。这允许您在距离达328英尺的接收器所在位置操作源设备的遥控器(播放,倒带,暂停等)。包括一个适配器电缆,用于将接收器的HDMI信号转换为DVI显示。
即插即用操作,快速设置和立即使用
包含的发射器和接收器单位可以直接使用,无需软件。包括安装硬件,可以将单元安装在墙壁、电线杆或19英寸机架上。Cat6补丁电缆 (例如Tripp Lite的N202-Series)可用于连接发射器到接收器或网络交换机。使用HDMI电缆(例如Tripp Lite的P568-或P569-Series)将额外显示器连接到发射器的本地输出,以监视传输到远程显示器的图像。
符合TAA的GSA计划采购
B160-101-DPHDSI符合联邦贸易协议法案 (TAA),使其有资格参加GSA(总务管理局)计划和其他联邦采购合同。
典型应用
- 将视频源放在安全位置,将显示器放在其他位置供预期观众观看
- 创建一个易更新的视频板,传达动态信息,如餐厅菜单或戏剧时间表
- 在机场或火车站中显示到达、离开和最新信息
- 在多个显示器上复制音频/视频内容,在多个屏幕上显示不同内容或创建由许多显示器组成的令人印象深刻的视频墙(需要多个发射机和接收器)
系统要求
- 具有DisplayPort输出的源设备(媒体服务器,笔记本电脑)
DisplayPort to DVI/HDMI Extender Kit for Trade Shows, Schools and Other A/V Applications
Tripp Lite’s B160-101-DPHDSI extender kit converts a DisplayPort signal to an IP-based signal for transmission to a DVI or HDMI monitor or projector via Cat5e/6 cable. It includes one Tripp Lite B160-001-DPSI transmitter and one B160-100-HDSI receiver and is perfect for classrooms, trade show booths, convention centers, movie theaters, hotel waiting rooms, places of worship and other applications where the source and display need to be located in different areas.
Typical Applications:
- Display arrival and departure information in an airport or bus terminal from a source located in a different area
- Use your DisplayPort laptop to give a video presentation in a boardroom, conference room or auditorium
Sends a High-Quality Signal Up to 328 ft.
In a point-to-point installation, this extender kit lets you place your monitor or projector up to 328 ft. (100 m) from your source. That’s more than 200 feet farther than a traditional Cat5e/6 solution will allow. It supports HD picture quality at resolutions up to 1920 x 1080 (1080p) at 60 Hz.
- Sends an audio/video signal up to 328 ft. in a point-to-point installation
- Supports HD resolutions up to 1920 x 1080 (1080p) at 60 Hz
Allows You to Scale Up to a Multi-In/Multi-Out Installation
Connect an Ethernet switch with Internet Group Management Protocol (IGMP) to create an installation with multiple sources and displays. Add multiple managed switches to create a multi-in/multi-out installation with up to 64 transmitters and 255 receivers. The IGMP-enabled switch will provide centralized control over which sources transmit to which displays.
- Supports the addition of an IGMP-enabled switch for multiple sources and displays
- Supports the addition of multiple managed switches for multi-in/multi-out installations
Ready to Use Right Out of the Package
With no software or drivers required, the B160-101-DPHDSI’s transmitter and receiver are completely plug-and-play. Included hardware supports rack-mount, wall-mount or pole-mount installation.
- Plug-and-play installation
- No additional software or drivers required
- Included hardware for rack-mount, wall-mount or pole-mount installation
TAA-Compliant for GSA Schedule Purchases
This extender kit is compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases and other federal procurement contracts.
Return Policy |
Time to Return |
Standard Return Policy |
We offer a hassle-free 30-day returns policy for domestic (US) orders, excluding non-refundable items. Refund or Replacement within 30 days of the delivery date. All products that fall under the Standard Return Policy qualify for our 30-Day Hassle-Free Returns. Please see the section above for more details. |
Replacement Only Return Policy |
Replacement within 30 days of the delivery date. |
Manufacturer Only Return Policy |
Covered by the manufacturer's warranty. Please refer to the terms and conditions for the manufacturer's warranty or contact the manufacturer. |
Holiday Extended Return Policies |
Extended Holiday Return Policy.Qualifying purchases of products displaying the " Extended Holiday Return Policy ", from November 1st, 2023 to December 25, 2023, are eligible for a Refund or Replacement until January 31, 2024. Extended Holiday Replacement-Only Return PolicyQualifying purchases of products displaying the " Extended Holiday Replacement-Only Return Policy ", from November 1st, 2023 to December 25, 2023, are eligible for a Replacement until January 31, 2024. |